![]() I can hear the relays clicking but there's no output voltage. It worked well for a few days and then not so much. ![]() I'm having a problem with the relays on the Sainsmart board. If I connect the solenoid to one of the working ports of my 16 Port Sainsmart it works without issue. Next I test and it hasn't worked a single time. I connect one of the grounds of my 24V power supply to the GND on the other side of the MOSFET board (Same side as OUT1-OUT4 / VCC)įinally I connect OUT1 on the MOSFET directly to my solenoid. I connect the + from my 24V power supply (Solenoid is capable of 5v-36v) directly to my solenoid. I connect the Power/Ground (VCC/GND on the same side as IN1-IN4) to the + and - outputs of my 24V power supply. I connect the outgoing port from my LEDWIZ (8 in this case) to IN1 of the 4-Channel Mosfet. I am guessing I have it hooked up incorrectly? Maybe somebody could tell me if this sounds right? ![]() The issue is I cannot get it to work with my LEDWIZ. So, I read this thread and picked up a couple 4-Channel DC 5-24V Green Board to work with my 4 solenoids. I have the 1N4007 Diode in place on each of my solenoids. I have replaced the board 3 times now due to ports no longer working. This issue is ONLY isolated to my solenoids. Long story short I am experiencing the same issue with ports on my 16 port Sainsmart relay burning out. I don't have a good understanding of how most of this stuff works at the electrical level but I can' follow directions pretty well. little bit confused why its not working and instantly triggering as soon as i connect to the controller board.Īny help would be greatly appreciated. I just hooked my contactor up with this method on a pinscape (kl25 board) and as soon as i connect the output 1 wire to the pinscape board it triggers the contactor instantly, in the software the on/off trigger doesn't seem to work at all, i'm using 12V +/- from the pc psu and from the diagram on the opposed side the single ground is coming from the other 24v PSU that controls the contactor, + from that PSU hooked straight upto the contactor's + and ground to the mosfet board same one as your diagram and as i just menioned. I put one of these in between the shaker motor and the output board because sometimes a shaker motor would just go crazy ![]() I used one of these with a LEDWiz -> 4-Channel DC 5-24V Then the motor plus and motor negative hook to the shaker motorĮdited by Outhere, 16 December 2021 - 05:44 PM. To hook this up take the OUT wire and hook it to the power negative, take the 12+ wire from the power supply hook it to the power + I put one of these in between the shaker motor and the output board because sometimes the shaker motor would just go crazy Power Supplies for Feedback - See link next lineĭon't forget about Diodes -> 53. You may want to add a fuse in the circuit Then pick one of the outs and that will go to the shaker motor or solenoid On other side of the board hook the ground from the power supply to GND Run appropriate Power to the ground and VCC next to the input LEDWiz Setup With 4-Channel DC 5-24V Board Wiring correct? I will admit-it seems a little off to me. Feels off.ĭOF question-without a voltage adjustment-anyone have a good intensity setting for the Stern Shaker Motor (from Pinball Life)- no control board in play. Shaker engages but buzzes first and then shakes. I have configured DOF to have Shaker on output channel of LEDWiz and turned the intensity down to 1 to 12- At 48 it shakes the holy hell out of the cabinet. Negative from Shaker to NO of Sainsmart- Port 7 Ground from Power Supply to Positive of Shaker Output from Sainsmart board to LedWiz- In this case port 7.ġ2V from Power Supply to Common on Sainsmart relay board- Port 7 In Play-12 v ATX jumped Power Supply (also supplying 5v for LED Matrix and side LEDs which works fine) LedWiz (running fine for all buttons and Contactors (8) and SainSmart 12 V/5V board- (new to install and using only as a relay).ĭOF runs fine minus the Shaker-no other cabinet issues that I am aware of:ġ2V in and Ground from ATX to Power on Sainsmart (distributed from block) I even found and followed the Major Frenchy online video's (thanks BTW) I followed the PinScape Build Guide v2 and still seem to have some issues. For the life of me, I cant get this to run 'correct' (I don't think).
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |